Phantom 4 - Gimbal "LIMP" on the 2nd boot ...

[sinxa]

I have this phantom 4 along with my other drones (phantom 3 standard, phantom 3 advanced, mavic pro).
I never had any crash specialy on this phantom 4. But this problem occures since the last 3 month.
Gimbal only works on the first (cold) boot. And it goes limp on the 2nd boot. While the video feed is just fine.
I have tried to refresh firmware (2.00.0700), downgrade (2.00.0106), re-upgrade (to 2.00.0700) .
recalibrate the gimbal, imu, vision, compass all of them but the problem is still there.

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

Anybody knows what's wrong with my phantom 4??
Thank's...

 

[Deleted member 62848]

I have this phantom 4 along with my other drones (phantom 3 standard, phantom 3 advanced, mavic pro).
I never had any crash specialy on this phantom 4. But this problem occures since the last 3 month.
Gimbal only works on the first (cold) boot. And it goes limp on the 2nd boot. While the video feed is just fine.
I have tried to refresh firmware (2.00.0700), downgrade (2.00.0106), re-upgrade (to 2.00.0700) .
recalibrate the gimbal, imu, vision, compass all of them but the problem is still there.

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

Anybody knows what's wrong with my phantom 4??
Thank's...

Yeh that's a very odd one,I had a Limp one once but not like that,if gimble calibration or imu calibration not fix it and it's new,I would exchange it,,,,,on the inteligent flight modes is yours turned on,,probly dumb question,but just ask

i

 

[Brockrock]

I have this phantom 4 along with my other drones (phantom 3 standard, phantom 3 advanced, mavic pro).
I never had any crash specialy on this phantom 4. But this problem occures since the last 3 month.
Gimbal only works on the first (cold) boot. And it goes limp on the 2nd boot. While the video feed is just fine.
I have tried to refresh firmware (2.00.0700), downgrade (2.00.0106), re-upgrade (to 2.00.0700) .
recalibrate the gimbal, imu, vision, compass all of them but the problem is still there.

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

Anybody knows what's wrong with my phantom 4??
Thank's...

You question if this could be temperature related in the video. I wondered the same thing. If it were me, I would take the gimbal off in order to re-seat the ribbon cables. It's not a difficult job as long as you have the proper tools and are very careful with the connectors and cables.

 

[sinxa]

Yeh that's a very odd one,I had a Limp one once but not like that,if gimble calibration or imu calibration not fix it and it's new,I would exchange it,,,,,on the inteligent flight modes is yours turned on,,probly dumb question,but just askView attachment 101211i

I think the warranty was expired already since few months ago....
And yes, inteligent flight mode was enabled. I always set it on every drone i purchased.

 

[sinxa]

You question if this could be temperature related in the video. I wondered the same thing. If it were me, I would take the gimbal off in order to re-seat the ribbon cables. It's not a difficult job as long as you have the proper tools and are very careful with the connectors and cables.

The ribbon cable is just replaced by the official dji repair shop due to the previous problem, some dot / vertical lines on the footage ....

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

..
If it was really caused by not well seated ribbon cable, i think this "limp" problem would occure a whole time since the time it was replaced. Don't you think so?

 

[Brockrock]

The ribbon cable is just replaced by the official dji repair shop due to the previous problem, some dot / vertical lines on the footage ....

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

..
If it was really caused by not well seated ribbon cable, i think this "limp" problem would occure a whole time since the time it was replaced. Don't you think so?

Hard to say for sure. The only variable seems to be temperature, so if the ribbon cable is not properly seated or slightly corroded, a tiny bit of expansion could explain it.

 

[sinxa]

Hard to say for sure. The only variable seems to be temperature, so if the ribbon cable is not properly seated or slightly corroded, a tiny bit of expansion could explain it.

Thanks for your answer, i had that "temperature variable" too in my mind.
But, what do you mean by "expansion"?