Sounds pretty much what I said. I said they use them as a parts kit and fine tune them.A message regarding the differences in the terminator panel versus cheap Chinese panels:
"Thanks Mike .
we have also changed a few things , the connectors will be SMA in the next batch ( T2 ) . the antenna comes with the patch cables and
the 3D bracket , these are peak tuned and give the best $$$ value there is in any antenna out there , its cheaper than the DBS o2 and out performs it easy also it does have better performance over the MaxxRange.
These are peak tuned and sealed for very rugged use and to keep them in tune in all conditions , like if you shock the Maxxrange it will mess the antenna up , you can drop the terminator it will not detune . We build them to last, there is no point re inventing the wheel with this type of antenna we used existing stuff that was out there and made it work properly ,this give the customer the best it can be and at a cost effective price , a normal person will not be able to do this , although the chineess ones on eBay would probably out perform the FPVLR v2. , but they are mass-produced , ours are hand built and tuned to perfection.
thanks"
I have personal experience with this regarding the maxxrange, I shared with you guys earlier in the thread when I opened up the two panels that the max range had the corners of the antenna peeled up from the sticky tape that held it in place. While I've never had an issue with range yet with my
maxxrange, I could see a scenario where bumping it around in the bag a few times could cause that tape to fail again. And it appears that Horizon is taking measures to make the terminator more secure than the maxx and the Chinese panels!
So you may have SOME success w/ the cheap panel but if extreme distance or penetration is what your seeking then the cheap panel will fall short and you get what you pay for!Sounds pretty much what I said. I said they use them as a parts kit and fine tune them.
Yet to be seen. The biggest tune up I would think is spacing and being able to keep the spacing correct.So you may have SOME success w/ the cheap panel but if extreme distance or penetration is what your seeking then the cheap panel will fall short and you get what you pay for!
I guess one of you is going to have to take your cheap panel out to 9 miles to find out[emoji41]Yet to be seen. The biggest tune up I would think is spacing and being able to keep the spacing correct.
I agree with that. I can go parity far with my cheap panels, but if I was going to do it every other day or so I think I would want the best. And I don't think I will be pushing it beyond 3 miles.So you may have SOME success w/ the cheap panel but if extreme distance or penetration is what your seeking then the cheap panel will fall short and you get what you pay for!
The problem with going the kind of distance as it takes to break or even get close to record these days is you got to have perfect reception out and back there's no room or battery life for you to hit a situation you lose signal for even a minute and risk a return to home situation where you're running 22 miles an hour when it's critical that you run 30+ miles per hour all the way back!I agree with that. I can go parity far with my cheap panels, but if I was going to do it every other day or so I think I would want the best. And I don't think I will be pushing it beyond 3 miles.
A message regarding the differences in the terminator panel versus cheap Chinese panels:
"Thanks Mike .
we have also changed a few things , the connectors will be SMA in the next batch ( T2 ) . the antenna comes with the patch cables and
the 3D bracket , these are peak tuned and give the best $$$ value there is in any antenna out there , its cheaper than the DBS o2 and out performs it easy also it does have better performance over the MaxxRange.
These are peak tuned and sealed for very rugged use and to keep them in tune in all conditions , like if you shock the Maxxrange it will mess the antenna up , you can drop the terminator it will not detune . We build them to last, there is no point re inventing the wheel with this type of antenna we used existing stuff that was out there and made it work properly ,this give the customer the best it can be and at a cost effective price , a normal person will not be able to do this , although the chineess ones on eBay would probably out perform the FPVLR v2. , but they are mass-produced , ours are hand built and tuned to perfection.
thanks"
I have personal experience with this regarding the maxxrange, I shared with you guys earlier in the thread when I opened up the two panels that the max range had the corners of the antenna peeled up from the sticky tape that held it in place. While I've never had an issue with range yet with my
maxxrange, I could see a scenario where bumping it around in the bag a few times could cause that tape to fail again. And it appears that Horizon is taking measures to make the terminator more secure than the maxx and the Chinese panels!
Db how much battery did you have left at 9 miles. I was looking at 9 miles out I would be deep in Indian ground....I guess one of you is going to have to take your cheap panel out to 9 miles to find out[emoji41]
NONE!Db how much battery did you have left at 9 miles. I was looking at 9 miles out I would be deep in Indian ground....
Ok thanks.
NONE!
Even with my best battery combination, at least in my area, and probably anybody who tries, it's hard to get out 9 miles and make it back! It takes every bit of skill, battery, and signal that you got at your disposal. More peopleDb how much battery did you have left at 9 miles. I was looking at 9 miles out I would be deep in Indian ground....
Which one. The Terminator is making one for the Standard version of p3 and I'm not sure on the Maxx . But I'm sure one of the others will answer it for you. The Terminator's version for the Standard is in the testing stage..Are they available for P3S?
We use essential cookies to make this site work, and optional cookies to enhance your experience.