Phantom 2 v2.0 w/ H3-3D
GoPro Hero 3+ Black Edition w/ BlurFix filters
ImmersionRC 600mw video transmitter
Black Pearl RC801 (7ch) diversity receiver/monitor
iOSD Mini
FPVLR Premium Combo antennas
Rave Aerial monitor mount
Flytrex Core 2
Shapeways landing gear extensions with built-in ImmersionRC vTx holder
RIT dyed props (Cherry Red and Blue Jean pictured below except where noted(
I just installed the Shapeways landing gear extension pieces and they fixed a few minor annoyances for me:
- gimbal no longer bangs the ground surface upon startup
- video transmitter is not mounted without adhesive (transmitter housing is secure yet removable - no chance of accidental detachment)
- video transmitter antenna is side opposite to compass
- video transmitter antenna can sit below the gimbal without touching the ground
- P2 still fits in my hard case and backpack with pre-cut foam
Gimbal startup not touching the table:
[youtube]https://www.youtube.com/watch?v=ATZTTnetrYk[/youtube]
Dyed props in slow motion:
[youtube]https://www.youtube.com/watch?v=4dllAKOuhSk[/youtube]
***props as pictured above are Scarlett Red and Royal Blue from RIT (the props below are all Cherry Red and Blue Jean from RIT)
***Note the Limefuel battery installed: initial impressions - good, not great, build quality; doesn't "snap" in as easily as OEM battery
Next mod: hoping to get the plug and play yaw mod if it becomes available
And the NDJ6 RC:
Put on a new decal today. Forgot to take part of the old decal off (oops).
And I used Plastidip on my old RC. Thinking about doing it to the new one.
Replaced my Rave Aerial monitor mount with this one from Shapeways today. I like it for three reasons:
1) it's smaller
2) faster to attach/detach with the GoPro style mount
3) adjustable for optimal viewing angle
Bought a top shell from eBay so I could switch the decals.
GoPro Hero 3+ Black Edition w/ BlurFix filters
ImmersionRC 600mw video transmitter
Black Pearl RC801 (7ch) diversity receiver/monitor
iOSD Mini
FPVLR Premium Combo antennas
Rave Aerial monitor mount
Flytrex Core 2
Shapeways landing gear extensions with built-in ImmersionRC vTx holder
RIT dyed props (Cherry Red and Blue Jean pictured below except where noted(
I just installed the Shapeways landing gear extension pieces and they fixed a few minor annoyances for me:
- gimbal no longer bangs the ground surface upon startup
- video transmitter is not mounted without adhesive (transmitter housing is secure yet removable - no chance of accidental detachment)
- video transmitter antenna is side opposite to compass
- video transmitter antenna can sit below the gimbal without touching the ground
- P2 still fits in my hard case and backpack with pre-cut foam
Gimbal startup not touching the table:
[youtube]https://www.youtube.com/watch?v=ATZTTnetrYk[/youtube]
Dyed props in slow motion:
[youtube]https://www.youtube.com/watch?v=4dllAKOuhSk[/youtube]
***props as pictured above are Scarlett Red and Royal Blue from RIT (the props below are all Cherry Red and Blue Jean from RIT)
***Note the Limefuel battery installed: initial impressions - good, not great, build quality; doesn't "snap" in as easily as OEM battery
Next mod: hoping to get the plug and play yaw mod if it becomes available
And the NDJ6 RC:
Put on a new decal today. Forgot to take part of the old decal off (oops).
And I used Plastidip on my old RC. Thinking about doing it to the new one.
Replaced my Rave Aerial monitor mount with this one from Shapeways today. I like it for three reasons:
1) it's smaller
2) faster to attach/detach with the GoPro style mount
3) adjustable for optimal viewing angle
Bought a top shell from eBay so I could switch the decals.