Crashed my drone and replaced the yaw arm and flat ribbon. The drone will fly, gimbal goes up and down on its own during start up but you can’t see anything from my screen. I have a camera sensor error and a calibrate error. I connected it to the DJI Assistant 2 and was successful in...
Hi all, crashed my P3 Advanced and have since replaced the broken roll and yaw arm, along with the ribbon cable. I currently have no gimbal movement on startup or otherwise and the video output is a garbled mess (picture included). I ensured all the cables where in tightly and am suspecting...
Crashed my Phantom 3 Standard and the camera came off. I believe the only real damage is the ribbon cable snapped and I'm trying to find a new one.
In Australia so going through offical DJI is a pain and expensive so I'm looking on ebay. My problem is all the cables seem to end in "PK" or "DA"...
So I have had my Phantom 3 Adv since 2015 and so far I have replaced the body once. After doing the shell replacement it flew great, I did a good job putting it back together. Then I have had video lag issues were the delay will range from 2-8 sec. I did a fix found here Phantom 3 Advanced Video...
My previously crashed P4 is on its way back from DroneFly. They repaired the entire camera/gimbal and explained DJI doesn't make parts available, only whole units. ERGO cost $799.00! OUCH!!!
Seems like such a waste. Broken gimbal arm and two torn ribbon cables; camera itself is unscratched.
Is...
I have unfortunately broke my p3s gimbal and in the process broke my ribbon cable along with the connector. I can find the cable easy but does anyone know where I can find the connector
Hey i have been searching help from all around internet but haven't asked here. My p3 Pro had small crash in low altitude and after changing the ribbon cable the camera/gimbal is not working properly. The gimbal shakes and goes into wrong directions. Also the image transmission shows only black...
When I replaced the shell on my P4 I desoldered the motor wires from the ESC boards. When I got it back together it seemed fine, but the motors were spinning backward. The motors responded to throttle commands. On checking it turns out I got the white and black wires reversed for all four...
As suggested in another thread post here where you can get Part 49 the flat flexible data ribbon cable for the PRO/ADV P3.
eBay:
DJI Phantom 3 Pro Adv Flexible Gimbal Flat Ribbon Flex Cable Part 49 dual layer | eBay
DJI Phantom 3 Pro Adv Flexible Gimbal Flat Ribbon Flex Cable Part
I have used...
Hello All, While doing an antenna upgrade to my Phantom 3 controller, I damaged the ribbon cable that connects the main board to the USB board on the back. I could NOT find a replacement cable ANYWHERE! Apparently, DJI does not sell this part. After a long time searching, I found a local...
Hello All, While doing an antenna upgrade to my Phantom 3 controller, I damaged the ribbon cable that connects the main board to the USB board on the back. I could NOT find a replacement cable ANYWHERE! Apparently, DJI does not sell this part. After a long time searching, I found a local...
Hello All, While doing an antenna upgrade to my Phantom 3 controller, I damaged the ribbon cable that connects the main board to the USB board on the back. I could NOT find a replacement cable ANYWHERE! Apparently, DJI does not sell this part. After a long time searching, I found a local...
Whats up im having a problem with my 3pro watch this !
As you can see in the footage, there is some wiggle/shake. The ribbon cable has been changed because of a crash. Does anyone have same kind of a problem.
Help would be great.
I crashed my DJI Phantom 3 Adv. During the crash the gimbal ribbon cable ripped and the gimbal roll arm broke. I ordered a new ribbon cable, roll arm and a pitch motor just in case the current pitch motor also got damaged during the crash. I just installed the new ribbon cable, roll arm and...
For anyone interested, I just received ribbon cables (32 pins) that perfectly fit the remote. I broke off mine while installing a DBS Mod. Will be happy to sell one and send it.
It works with the HDMI Module.
Please see the picture attached.
Send me a DM.
Ok so I just bought a Phantom 2 Vision Plus off my friend knowing that the ribbon cable and role motor were broken on the gimbal. I bought a new ribbon cable off ebay and glued the motor back into position. After hooking it back up and putting it together I turned on the phantom and nothing. The...
Just bought a new P3P and whenever I use video mode, there are random purple lines covering the screen. They happen at random but sometimes my screen is full of them. It doesn't happen in picture mode, which works without issue. This issue ruins all my videos so I'm pretty PO'ed as it is. I...
I broke my ribbon cable from the main board to the con board. I was hoping some one would be able to help me find a new or used one. I am going to try and attach pictures.
thanks for the help.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.