Tony dji phantom 4 Gimble motor overheat

[Tony wehbe]

Hi guys i wonder if any one can help here with my p4 drone gimble
I never had any crashes but once i did not fit one of the props properly and the drone did not take of the prop flew away and the drone went under the table and stopped flew ok after but i can tell the gimble is overheating when i touch it the camera has a little shake left and right and it seems loose and i get the yellow message (gimble Motor Overload)
Can you please give me idea what it is thanks

 

[Florida Drone Supply]

Is anything bent? It is very easy to mess up a gimbal on a P4 drone. Hard to say what the cause is without seeing it. I had this happen recently. It was the yaw motor that had the overload and I had to replace the gimbal. Best of luck on this one. Wish I could be more help.

 

[WV. Rootman]

It might also happen if the gimbal is rubbing up against the ribbon.

 

[Man with Drone]

Have you checked the Flux-Capacitor?

 

[Man with Drone]

Sorry I couldn’t resist.

 

[Tony wehbe]

Is anything bent? It is very easy to mess up a gimbal on a P4 drone. Hard to say what the cause is without seeing it. I had this happen recently. It was the yaw motor that had the overload and I had to replace the gimbal. Best of luck on this one. Wish I could be more help.

Nothing looks bent this happened after i took the drone out of the car and the temperature was very high the drone was hot and i flue it
But it was in the foam box in the car
When you fly the drone the camera shakes sideways but not a big shake
I did gimble automatic calibration and the camera was steady iuntill i turned the drone off and started to shake again
But when its hot i can’t Perform calibration
By the way when its calibrating its not moving left and right as usual

Hi guys i wonder if any one can help here with my p4 drone gimble
I never had any crashes but once i did not fit one of the props properly and the drone did not take of the prop flew away and the drone went under the table and stopped flew ok after but i can tell the gimble is overheating when i touch it the camera has a little shake left and right and it seems loose and i get the yellow message (gimble Motor Overload)
Can you please give me idea what it is thanks

Have you checked the

Have you checked the Flux-Capacitor?

 

[Tony wehbe]

What is the flex capacitor?

 

[Tony wehbe]

Have you checked the Flux-Capacitor?

Ithe

What is the flex capacitor?

The cable looks very good and not touching anything

 

[Tony wehbe]

Nothing looks bent this happened after i took the drone out of the car and the temperature was very high the drone was hot and i flue it
But it was in the foam box in the car
When you fly the drone the camera shakes sideways but not a big shake
I did gimble automatic calibration and the camera was steady iuntill i turned the drone off and started to shake again
But when its hot i can’t Perform calibration
By the way when its calibrating its not moving left and right as usual

My Dront is still shaking sideways slightly but i had message on the screen saying:
Gimble motor overload
No i got another one saying :
Vision sensor calibration
Connect to pc or mac
Anyone can help?

 

[Beerock]

Connect it to your PC and calibrate the sensors

 

[Tony wehbe]

Connect it to your PC and calibrate the sensors

Connect it to your PC and calibrate

 

[Tony wehbe]

Are you sure? Because its asking me to calibrate sensors

 

[Tony wehbe]

Are you sure? Because its asking me to calibrate sensors

But why you think this is happened?

 

[Tony wehbe]

My Dront is still shaking sideways slightly but i had message on the screen saying:
Gimble motor overload
No i got another one saying :
Vision sensor calibration
Connect to pc or mac
Anyone can help?

H

 

[Tony wehbe]

I just relised something now the gimble icover and the motor are overheating
And when i Automatically calibrate the gimble it gets calibrated without the camera moving left and right !!
Anyone knows what it is?

 

[swathinpat]

I just relised something now the gimble icover and the motor are overheating
And when i Automatically calibrate the gimble it gets calibrated without the camera moving left and right !!
Anyone knows what it is?

Hey, just wondering if you ever found a solution because my phantom 4 is doing the exact same thing and all I can think is to change the motors or the whole thing