motherboard

  1. feliminerva

    doing some research to make mods on a phantom 3

    hi guys, i'm new to this forum and i'm doing some research to decide wheather i'll buy a phantom 3a and mod it to be better(like changing it's motors, or adding some sensors, or even making the phavic conversion kit) or buy the 3pro/4 and just change it to phavic(for those who don't know what...
  2. BenjiHoggi

    Phantom 3 Std. Motherboard/ESC failure on power-on - Please Help

    Hello all, I'm asking for some help here because I'm losing my mind with frustration at what has happened to my drone. Let me explain. I'm a Phantom 3 Standard owner. I'm also a full time student, so this was a fairly large purchase and something I put a lot of time and research into. I...
  3. M

    ESC status error after hard contact with tree and a few seconds in shallow water

    Yes... I flew Phantom 3 Advanced into tree and it came down into shallow (about 4 inches of water near shore) water where I grabbed it less than 3 seconds later. Anyway, now getting "ESC status error. Restart aircraft." Searching internet and this forum suggest ESC errors might come from bad...
  4. Brent10

    SOLD: P2V+ Parts for Sale (motors, batteries, main board, controller + long range antenna)

    SOLD
  5. D

    Problem with my motherboard

    Hello everybody, I'm just about to repair my Dji phantom 3 pro 4k and noticed that somehow a few small components on my motherboard are broken. I would like to solder the individual components but I just can not find out what components were installed there (Unfortunately, there are no more...
  6. C

    Phantom adv camera mobo

    I recently crashed and I need a new gimbal motherboard for the advanced any suggestions of where I could get one it would be great. thanks
  7. J

    P3 Standard Link Button Replacement?

    So my P3 recently took a tumble, most of which i've replaced, not too bad damage, BUT I need to re-synch my controller to the aircraft and MY LINK BUTTON IS GONE. Does anyone know of any place I could get a replacement button/connection to mount it back to the motherboard, or should I just look...
  8. D

    Motor or ESC or Motherboard burned out?

    Currently all green lights, ready to fly... just motors "twitch" and wont spin nor takeoff. Background: removed the prop guards and the plastic mounting brackets, then mounted the motors with the same LONG screws... (believe the long screws interfered with magnetic field of motors, and now...
  9. T

    Motherboard components

    Hi, I'm a newbie and......I crushed my standard from 4 m! So after remounted gimball, camera, glued gimball support..... The bird fly and respond to command but the 2.4 g wifi doesn't work. The remote remain solid red no camera images, no info in dji app. Fly but is blind. In the mainboard the...
  10. P

    dji phantom 3 motherboard

    hey guys, i need help identifying a particular component on my dji phantom 3 motherboard. i opened the top and realized a small brownish yellow component had blown up ( i think it is a surface mount capacitor... however i could be wrong) see my picture please. anyways i have no warnings when i...
  11. P

    OPENED UP PHANTOM 3, CRUSHED CIRCUIT COMPONENT !

    REMOVED TOP OF PHANTOM 3 COVER and noticed a crushed a tiny circuit component that appears to be a resistor. (could be a diode, or some other unknown component.. it isnt labeled) Does anyone know if dji will replace the single tiny crushed component?? or do i have to purchase a new...
  12. K

    electrolytic capacitor loose

    Hi guys, I had a slight crash and I after that I heard inside of my Phantom 3 Adv noise. So I opened it up and I found damaged screw insert which is right beside one of the motor - picture no.1 And also I found loose electrolytic capacitor. I am not sure if its blown or just damaged. Picutres...
  13. jtuttleatl5

    Replaced P3P Motherboard - Still ESC Error :(

    Hi - I've spent hours on all the helpful threads researching any problems but am at a dead end so hoping for your help! Quick overview of the pass 2 months... 1) Crashed drone (my fault) 2) Replaced burnt out motor and shell (motor was black, shell warped due to heat of motor) 3) Rest of motors...
Want to Remove this Ad? Simply login or create a free account