LOL! How about a screenshot of the Go4 app? I had been looking at something else and had Go2 on my mind. Will post the screenshot shortly.
Hello. Old newbe here
- Thread starter Blufx
- Start date
Well, something had happened. It didn't connect when I started the control and AC, so I did the same reset procedure (C1, C2, record, camera dial) turned on the controller and didn't get a blue light. Or beep. I let up on the camera dial and it started blinking blue and beeping. I pushed the link button on the drone(beside usb) and it linked! Only it linked with the app this time. It getting dark out so I'll check it out tomorrow. I don't want to start a post on a flyaway. Thanks to everyone, I'll post tomorrow with an update.
WHOO HOO!!! It's healed! I took it up for a short flight to check it out and everything seems to be working right, but there's some strong wind gusts today. I'll post again when it's not so windy.
Thanks to everybody. I still don't know how it did it, but it's doing what we wanted.
Thanks to everybody. I still don't know how it did it, but it's doing what we wanted.
Well, it's not quite healed. It loses connection or video transmission. The picture freezes and turns gray scale. I also noticed even when the video is working the app isn't displaying distance or altitude. On the drone, the link button/light, is it supposed to have a steady green light, or flashing? And what does it mean when it flashes two red, then two green repeating? I've found three methods of linking. The first is in the app. Start app, touch the dots in upper right, then the controller icon, and remote controller linking. It asks to confirm frequency settings. I hit OK, and nothing happens. I think the controller is supposed beep and display blue light, but it doesn't. The next is for a different controller and involves pressing c1,c2, record, and camera dial, together then turn the controller off. The last is for my controller(GL300C) uses the same button combination, but you press all the buttons then start the controller. None of which worked until my finger slipped Off the camera dial and I got a blinking blue light and beeping. That's when I pressed the link button on the drone and mistakenly thought it linked. Now I cant get it link to the app anymore. Anybody know what I'm doing wrong?
RodPad
Premium Pilot
Thanks Rod,
I've tried 4 or 5 cables. Same results on all but 1 which obviously is just a charge cable.
Well, it looks like I run out of help here. I'm going to post again under Phantom 4 help. I'm assuming my post hasn't been seen much because I started talking about my problem in introductions.
RodPad
Premium Pilot
@Blufx,
Stay here, introductions thread doesn't matter, You got two members on this thread that know a lot more than I.
Without looking through the whole thread. Your answers were, were connected with the wrong post?
I think that is correct?
At the moment I'm not sure what to ask you.
Come back with mobile device type?
Which DJI app?
What lights come on the bird, and the remote.
That's all I can think at my level.
Rod ..
Stay here, introductions thread doesn't matter, You got two members on this thread that know a lot more than I.
Without looking through the whole thread. Your answers were, were connected with the wrong post?
I think that is correct?
At the moment I'm not sure what to ask you.
Come back with mobile device type?
Which DJI app?
What lights come on the bird, and the remote.
That's all I can think at my level.
Rod ..
Last edited:
I am still watching your post. When linked the far left light should turn solid green. Just a hunch, but I think you have a bad controller. If you were near me we could get this resolved quickly. hard to do this way. We are all just guessing at this point. Where are you located?
@Rod..no. I think I jumbled them up some by not knowing how to use the forum on my phone. I used to do it on my computer. I believe I answered some multiple times. But I got it now. You asked:
Samsung Galaxy Note 20Ultra
DJI GO4
Solid Red front/Yellow flashing rapidly rear then after it connects with the controller blinking yellow. A minute or so later it blinking green on rear. At this point the the link button between thr USB ports is flashing red x2 then green x2.
The app is connected to the internet but not the drone. The controller has solid green light.
Blu
RodPad
Premium Pilot
Great to get you back, I have a P4 that was giving to me from a member on this forum,
I haven't flown it yet.
Why I haven't yet? I need get back into the groove.
My help on this thread, is bugging the op
I don't use a mobile device to post or email and I will never have a F!book account.
There used to a mobile app for the Phantom Forums
Anyways, Ted had to do a workaround when it disappeared, I think he mostly uses a mobile device.
Rod ..
I haven't flown it yet.
Why I haven't yet? I need get back into the groove.
My help on this thread, is bugging the op
I don't use a mobile device to post or email and I will never have a F!book account.
There used to a mobile app for the Phantom Forums
Anyways, Ted had to do a workaround when it disappeared, I think he mostly uses a mobile device.
Rod ..
@RodPad is your P4 a standard like mine? My reason for asking is the possibility of comparing what mine does or doesn't do during the linking process.Great to get you back, I have a P4 that was giving to me from a member on this forum,
I haven't flown it yet.
Why I haven't yet? I need get back into the groove.
My help on this thread, is bugging the op
I don't use a mobile device to post or email and I will never have a F!book account.
There used to a mobile app for the Phantom Forums
Anyways, Ted had to do a workaround when it disappeared, I think he mostly uses a mobile device.
Rod ..
Similar threads
