roll motor

  1. W

    P4P V2 - Gimbal problem

    Hello. After a fall from ~3 meters a gimbal was injured. A view from camera was OK. I immediately took Phantom to the nearest drone shop with service (not the official DJI service) but after few weeks they told me that they don't now how to repair that. I've tried to realise what's up with...
  2. T

    phantom 3 standard crash and now gimbal malfunction

    Hi there , newbie here I had my drone out the other night and clipped it off a wall before i could steer it away. It fell about four feet causing the roll motor to separate from the casing which leads to the camera. The part still attached to the drone was the part that exposes the copper...
  3. W

    Gimbal Roll Motor just shutting off when i move it in max roll Position.

    I have this problem when i roll the motor too much the gimbal just shutting off but when i restart it again the motor is fine but when i roll too much the motor again it just shut off again i already replace the potentiometer in motor driver. what do i need to replace to not have this issue...
    • Wachenanggo
    • Thread
    • failure gimbal gimbal failure phantom 3 pro altimeter sonar phantom 3p roll motor
    • Replies: 0
    • Forum: Phantom 3 Pro/Adv
  4. P

    Which gimbal motor has failed? yaw, pitch, roll...

    When I turn on the P3, the gimbal does nothing. No crazy dance or anything. If I move it side to side, it will emit a faint buzz. The camera is fine, and live view and recording works. There is a "yaw error" in the Go app. Recalibrating doesn't fix it. The gimbal appears fine. No cracks...
    • PaulW
    • Thread
    • gimbal motor pitch roll motor yaw arm motor yaw error
    • Replies: 1
    • Forum: Phantom 3 Standard
  5. C

    Roll motor overloaded + tilted

    I've been having problems with my p4 for a while now. My gimbal started by "bouncing" during flight and sending me gimbal motor overloaded warnings. I did some research and decided to replace the yaw arm (because it was bent), the roll motor, and the gimbal ribbon cable. I did so and have seen...
  6. R

    Trying to find gimbal parts in stock

    I’m trying to fix a phantom here in Brazil, and need to find a roll motor, and a roll sensor board, and flex cable, all for the p2v+. I've been searching for US dealers online for these items in stock with no luck. I'm about to start emailing some of the companies, but decided to check here...
  7. K

    Replace Roll Motor on Gimbal

    Hi! So I recently experienced a crash and unfortunately the yaw arm was bent and has to be replaced. As I got to the last three screws holding it in place, the screws stripped and I am unable to remove the screws from the ROLL motor. I detached the other motor and the the roll arm so it's just...
  8. K

    Replace Roll Motor on Gimbal

    Hi! So I recently experienced a crash and unfortunately the yaw arm was bent and has to be replaced. As I got to the last three screws holding it in place, the screws stripped and I am unable to remove the screws from the ROLL motor. I detached the other motor and the the roll arm so it's just...
  9. T

    I have image transmission but a dead gimbal

    I crashed my DJI Phantom 3 Adv. During the crash the gimbal ribbon cable ripped and the gimbal roll arm broke. I ordered a new ribbon cable, roll arm and a pitch motor just in case the current pitch motor also got damaged during the crash. I just installed the new ribbon cable, roll arm and...
    • TimKah
    • Thread
    • gimbal image transmission not working pitch ribbon cable roll roll arm roll motor yaw
    • Replies: 8
    • Forum: Phantom 3 Pro/Adv
  10. A

    Roll Arm Ribbon Replacement

    While landing, my blade motors suddenly stopped at about 5 feet above ground. I have no idea why they just stopped. The crash broke several parts that I'm now needing to order and replace. One of those items is the roll motor. (picture attached shows the broken ribbon) However, I can't find a...