Recent content by sunrunner

  1. S

    Phantom 2 Vision Plus and Litchi Mission

    I have ( 3) Phantom 2 Vision + drones. I recently sent one on a short 4 minute Litchi mission (5 Waypoints). The mission went fine until I reached Waypoint 3. The Phantom hovered and turned around 1.5 times, paused and continue to the next waypoint. It reached waypoint 4, paused and did a...
  2. S

    Litchi and Mission Hub

    More Litchi mission issues. Today I flew my Phantom 2 Vision + on a short mission (6 waypoints). All went well, during the load process, and initiation, but during the mission on waypoint 3 the Phantom stopped and just hovered. Since it was only a 4 minute mission I waited to see if it would...
  3. S

    Litchi and Mission Hub

    I will try that. Thanks.
  4. S

    Litchi and Mission Hub

    I have a Phantom 3 Professional. In the past I have flown and saved missions and orbits. Today I flew and could not get the saved mission to upload. The icon came up on my tablet (android) which said start (the phantom was about 50' up and the select switch was on "F") but it would not load...
  5. S

    Phantom 2 Vision + V3.0

    Thanks Mike. I'm surprised the motors would run at all with a short. Working on getting some 2312 motors. I wish I could test each motor to know which one(s) have shorts?
  6. S

    Hi Mark. Thanks for the info about the problem I have with the motor(s) on my Phantom 2 vision...

    Hi Mark. Thanks for the info about the problem I have with the motor(s) on my Phantom 2 vision +. The interesting part of why my battery discharges so quickly due to the drain. The motor seems to run fine at idle speed and does rev up, but not enough for takeoff. I'm surprised with a short...
  7. S

    Phantom 2 Vision + V3.0

    I recently acquired a P2V+ 3.0. It came with the prop guards (the type that is more permanent and don't slide in and out). The unit looked pristine and the former owner claimed it had been sitting for 2-3 years. The prop guards were off, and I fired it up and noticed that one motor was barely...
  8. S

    Litchi and Mission Hub

    I recently flew my P3P on a mission that was set up on Mission Hub. I also synced my approved Samsung 10" tablet while on my wi-fi network. The mission flew fine with a couple of exceptions. While following the route on my tablet the bird was way ahead of what the route was showing on my...
  9. S

    Phantom 2 Vision + Gimbal issue

    Thanks. I will take a look at Gimbal connections and ribbon connections. The seller has agreed to accept the return. I may just return it. I have not reloaded the APP, but my android phone is showing the APP 1.0.61 Can anyone tell me the latest Camera APP? All though my P2Vision +...
  10. S

    Phantom 2 Vision + Gimbal issue

    I recently bought a new camera for my P2V+. All went well with the install. However it appeared that the gimbal had a lot of free play. Upon start up it would do the movements and point forward ready to go. After takeoff it would fall out of place and point up or down, sometimes pointing up...
  11. S

    Gimbal slightly points to left (but has level horizon)

    I recently added a Phantom Vision 2+. All is good, but in flight with the camera pointing slightly down the camera is slightly catching the left "front part" of my skid. The camera works properly, with not messages. Is there an adjustment to get it straight (slightly to the right)? Thanks
  12. S

    Anyone else had course lock mode just plain NOT work?

    Yes, I went to phantom assist, and low and behold the IOC was not checked. Checked it and now it works fine.
  13. S

    Anyone else had course lock mode just plain NOT work?

    Thanks Dale. I will give that a try, which can be observed on the Phantom Assistant when hooked up (which should show me if it is opening or closing?).
  14. S

    Anyone else had course lock mode just plain NOT work?

    I have a Phantom 2 (just got it) and my course lock mode will not engage. The LED's do not show (yellow) that it's in IOC mode. Every thing else on the remote works fine. Could this be a firmware issue? I did do all the updates recently on the firmware. Any ideas here? :?: