Recent content by Spazz_MMCF

  1. Spazz_MMCF

    My P3S Skin

    Thanks.. so this is to the very edge of the graphic layout? Not the border of the file... correct?
  2. Spazz_MMCF

    My P3S Skin

    Ok... my graphics guy can read it and cut... but he needs to know the size and I have no idea what to tell him. Is there a 'size' that he needs to shrink it to? The pattern file is HUGE!!! THANKS
  3. Spazz_MMCF

    Reno, NV- Truckee/Tahoe, CA- The Sierras

    6+ inches when I woke up.... Then shoveled from 4 to 5am
  4. Spazz_MMCF

    Reno, NV- Truckee/Tahoe, CA- The Sierras

    I'm up in Stead... lots of wind and a few flurries right now... they always get it wrong here... I believe Downtown Reno is in the no fly zone for the airport...even though it would be a cool video to start around 4th st and go south down S Virginia to the arch....
  5. Spazz_MMCF

    Reno, NV- Truckee/Tahoe, CA- The Sierras

    STORMAGEDDON is supposed to hit tomorrow, 1 March.... with lots of snow.. calling for around 4+ feet in partrs of the Sierras... What area you talking about? Reno is looking at a good amount of snow in the valley as well if the reports are correct.
  6. Spazz_MMCF

    Catchy drone business names?

    SKY-I Aerial Imaging
  7. Spazz_MMCF

    PhantomPilots and DJI Website

    Its a settings issue in Chrome.... I use Chrome exclusively and no such thing ever happens How are you loading this site? Do you have a bookmark? typing it in? Check your STARTUP section on the Chrome Settings.
  8. Spazz_MMCF

    MicroSD Recovery

    Funny this came up.. I was videoing with my Galaxy S8+ and phone locked up... when I rebooted... 16gb microsd card was not found and empty to the phone... I have easeus recovery software... only recognizes the card as a lost partition and disappears... Lucky for backup software....I didn't...
  9. Spazz_MMCF

    Peavine Mtn View in Reno, NV

    Thanks... it's too cold to fly lately... 4 degrees and high of 20... miss flying and shooting vids. I have a really cool spot I need to get to when the weather breaks
  10. Spazz_MMCF

    My P3S Skin

    I have a graphics guy... sending him the file to see if he can do something for me
  11. Spazz_MMCF

    My P3S Skin

  12. Spazz_MMCF

    My P3S Skin

    Love it! Wanna share the cut file? I would if it's the same for the P3SE.. any idea?
  13. Spazz_MMCF

    P3SE taking longer than normal to 'WARM UP'

    Ok guys..52 degrees outside... let it sit outside for 30 minutes with the battery out... Brought it in and did an IMU calibration, then a gimbal Calibration. I shut it off for about 5 minutes... then videoed the startup... IT ONLY TOOK A FEW SECONDS to be ready to fly... Check out the video...
  14. Spazz_MMCF

    P3SE taking longer than normal to 'WARM UP'

    I'l give it a try... my outside temps at night are below 30F... so I'm thinkin 15 minutes or so is all I would need. Thanks
  15. Spazz_MMCF

    P3SE taking longer than normal to 'WARM UP'

    So I noticed over the last few flights... when I connect to DJI GO ( after I power up remote, then AC... link to AC and launch DJI GO ) The upper left message ( in orange ) that says WARMING UP is now taking 30 -45 seconds when it used to take only 10-15 seconds before it turns green and says...