Recent content by Pierre

  1. P

    disconnected

    I finally got the USB settings set correctly on my phone, and can now get the greyed out Camera icon, but it won't connect, no telemetry. I should be expecting a blue Camera icon in the app. Once in camera view I get the 'Disconnected' message in the top bar. I can control the motors on/off and...
  2. P

    disconnected

    It still has the original USB board. When I was looking for replacement parts it looked like the USB/HDMI board is the only board available, and seems to be compatible. The only link procedure I can do is with the C1/C2/record button hold until it beeps, followed by the right dial press down...
  3. P

    disconnected

    I also tried another P3P remote, and I'm getting the same behavior after binding to it, with the buttons sequencing. That other system was also updated to the latest firmware. I'm still struggling to figure out of it's a firmware thing, or a hardware issue (USB/HDMI board in the controller...
  4. P

    disconnected

    I'm getting a flashing green light on the RC. I tried 7 different USB cables. I tried with an HTC phone and a Samsung tablet, re-booting while connected with the cable, unplugging/re-plugging the cable. With the tablet I'm getting a grey camera icon on the app, which goes to the camera view...
  5. P

    disconnected

    I upgraded the GO app to 3.1.5, Android version, now I'm stuck on the 'How to Connect', and can't get any telemetry. I can't start the motors anymore. This is driving me nuts. From the main page, long press on the menu icon on the top right, I'm not getting any information from the firmware...
  6. P

    disconnected

    Same problem here on a P3P. I tried different USB cables, different phone and tablet. Could it be the wifi module? I'm not seeing any Phantom network on my wifi analyzer app. The other possibility is that the USB module on the controller died, as mentioned in this video: I opened up the...
  7. P

    Recycling P2V+ guts

    I've got a crashed/damaged P2V+ I would like to repurpose the guts to another frame, rather than swapping the shell, as I've got a F450 bare frame already. One of the ESC was also damaged, but the rest of the electronics looks fine. Can the Phantom flight controller be used on its own with an...
  8. P

    P3P Repair gone bad

    Just found the problem. I had tried two different USB cables, but the third one was fine. The first two were either bad, or just charging cables.
  9. P

    P3P Repair gone bad

    After replacement of the main board and motors, I can't get the GO app to link to the P3P. The RC link works, as I'm getting green LEDs on the remote and drone, but I can't turn on the motors. The gimbal is not installed or connected, but I was able a few months back to connect to the app after...
  10. P

    P3S not connecting to DJI Go app

    Yes, the RC controls from the remote were acting on the Phantom. Yes, it worked, the remote LED turned green and the app worked just fine after that to get data/video from the Phantom.
  11. P

    P3S not connecting to DJI Go app

    Many thanks Rod, that was it! I never clued in that the red LED on the remote meant is wasn't linked. What threw me off is that I still had RC control, but no connection to the app.
  12. P

    P3S not connecting to DJI Go app

    I tried the GO app on a different Android device, and it shows the same symptoms. Could the wifi module in the Phantom be blown if it just won't been seen by the app?
  13. P

    P3S not connecting to DJI Go app

    I tried a previous FW version and got the following txt file, but still can't seem to connect to the aircraft. ========== 2014.01.01 00:00:14 remo-con disconnect====== Packet: P3C_FW_V01.06.0080.bin Upgrading ... Result: Success. ========== 2014.01.01 00:00:13 remo-con disconnect====== Packet...
  14. P

    P3S not connecting to DJI Go app

    I just did that, but still no go. I got the following message on the SD card: ========== 2014.01.01 00:00:14 remo-con disconnect====== Packet: P3C_FW_V01.06.0080.bin Upgrading ... Result: Success. Should I downgrade the firmware?
  15. P

    P3S not connecting to DJI Go app

    I just did that, but still no go. I got the following message on the SD card: ========== 2014.01.01 00:00:14 remo-con disconnect====== Packet: P3C_FW_V01.06.0080.bin Upgrading ... Result: Success. Should I downgrade the firmware? I'm running v 3.0.1 of the Android GO app.