Recent content by Grumpy

  1. G

    I found this to override params

    Looks like it will work for any version. I did notice that in RED it shows 9000 in altitude... if I change this to 500 I get the warning saying you agree, it changes the 500 to blue and locks it in, it wont allow me to change it back to 9000. Going to try and flash it again and see if it takes...
  2. G

    What is the ideal FW and SW version to downgrade to?

    Thanks. Still need to know how to link the two on the roll back. Thx
  3. G

    What is the ideal FW and SW version to downgrade to?

    Thanks. I rolled it back to 1.7.6 and the app to 2.4.3. I am able to do to the 32 channel mod and override the speed, alt and distace, zones, etc. I have noticed that in the About section of the app software it does NOT show the version. How do I sync that up? Thanks.
  4. G

    Hey... can you tell me what the ideal FW for the aircraft and software for the controller is? I...

    Hey... can you tell me what the ideal FW for the aircraft and software for the controller is? I see where the RX output was decreased after v1.5 but then I see where 1.5 may have a bug. Should I roll back this far or stay at 1.6 for the 32 channel hack or some other version. Your feedback is...
  5. G

    Downgrading firmware on P3P from 1.10.9 to 1.7.6

    Thoughts on roll back. I was thinking back to 1.6 which offers the 32 channel hack. With the controller at 2.4.3. Is that not the best option? I see where some went to 1.5 for the increased TX output... but then I see dont use 1.5 due to known bug. Can someone clarify what would be the ideal FW...
  6. G

    What is the ideal FW and SW version to downgrade to?

    Thanks! Does anyone know if I should roll back before 1.6 to 1.5 that has the increased output? I saw where 1.5 had bugs... What is the ideal FW and software combo? Thanks! https://phantompilots.com/threads/downgrading-firmware-on-p3p-from-1-10-9-to-1-7-6.105384/
  7. G

    What is the ideal FW and SW version to downgrade to?

    Decided to go with the 1.7 version. Do I need to downgrade the controller? Or is the current version ok? Thanks. If so, which controller version do i need for the FW 1.7? I see where power output was cut between 1.5 and 1.6.. but some have indicated not to use 1.5.. is that correct? Thanks...
  8. G

    What is the ideal FW and SW version to downgrade to?

    Im sure this has been discussed before, but it seems that everytime there is an update, especially the lastest one... which Ive been using for a while I ALWAYS have issues. Usually transmission issues. Last time the F%@%@% thing literally crashed into my truck as I lost control and transmission...
  9. G

    Having issues with calibrating compass

    Thx. What should I be looking for? It also says strong interference, not sure if Marco or what.
  10. G

    Where to find a three way antenna bar?

    Took advice on panel ant. Wow is all I can say. Thx.
  11. G

    Having issues with calibrating compass

    This has been going on for some time. The only mods I have are a maxuav panel and 5 watt amp. On the drone itself I have a Marco polo hot glued on the right hand side rear battery compartment. Pretty much to the housing lip where the bat goes It wont calibrate no matter what I do and there is...
  12. G

    Where to find a three way antenna bar?

    I would like to do an antenna upgrade but I dont want the antennas that come with the antenna bar and would rather match my own. Anyone know where to get just the 3 way antenna bar? Thx
  13. G

    Stress cracks and epoxy

    Yes, but I went up to the small ridge around each shaft. No further. The area directly below the motor has a thin coating of resin and carbon/kevlar strands.
  14. G

    Stress cracks and epoxy

    Thanks. Used carbon fiber/kevlar 1/4" strands. Came out nice. Just waiting for the resin to harden.