P2+ TX Mod with Inspire1 tab mount

Joined
May 15, 2014
Messages
77
Reaction score
12
I really liked the inspire1 tab mount so i did a mod to my P2+ TX and put it on it, way better then the other options. I used a 1/4-20 nutsert for the mount to screw in, I think it turned out good..
 

Attachments

  • 20150503_160229.jpg
    20150503_160229.jpg
    493.6 KB · Views: 1,918
  • 20150503_160239.jpg
    20150503_160239.jpg
    575.4 KB · Views: 1,825
  • 20150428_081059(1).jpg
    20150428_081059(1).jpg
    569.6 KB · Views: 1,900
  • 20150428_081122(2).jpg
    20150428_081122(2).jpg
    586.2 KB · Views: 1,847
  • 20150428_081046.jpg
    20150428_081046.jpg
    769.4 KB · Views: 2,099
I really liked the inspire1 tab mount so i did a mod to my P2+ TX and put it on it, way better then the other options. I used a 1/4-20 nutsert for the mount to screw in, I think it turned out good..
I would like to do the same to use an 8.9" kindle fire unit and my P2v+ TX. Could you elaborate a little on the nutsert and what and how you drilled the case. I am afraid my technical skills are not nearly as good as yours and would hate to destroy the case. Also what is the mount called so i can look it up on Ebay. Thank You
 

Attachments

  • 10999613_10152683703335882_3305539028255320663_o.jpg
    10999613_10152683703335882_3305539028255320663_o.jpg
    255.8 KB · Views: 934
Thank You. How and what did you use to drill the case?
Just drill a hole that is a little smaler than the screw. I did find the position by holding the bracket sideways...left and right. Then make a pencil mark at both positions,and draw a line..... Then hold it in the center.... :) I did only use a little bit force and screwed it into the controller.... just remember that the wires inside goes straigh under it ...;-)
 
Last edited:
  • Like
Reactions: Chum Dumpster Plus
Mod for my Samsung Tab S 10.5" to "fit" on the Inspire 1 Holder
20150504_195411.jpg
 

Attachments

  • 20150504_194139.jpg
    20150504_194139.jpg
    4.6 MB · Views: 1,041
  • 20150504_194212.jpg
    20150504_194212.jpg
    2 MB · Views: 951
  • 20150504_194347.jpg
    20150504_194347.jpg
    4 MB · Views: 960
  • 20150504_194959.jpg
    20150504_194959.jpg
    1.3 MB · Views: 961
  • 20150504_195035.jpg
    20150504_195035.jpg
    4.2 MB · Views: 993
  • 20150504_195706.jpg
    20150504_195706.jpg
    2.6 MB · Views: 925
LOL.. just start with with a pilot hole first,"Small Drill" then work your way up to the right size.
Thanks I may end up there anyway if this doesn't work. I found this here on the site. If it does not work, I am out 40 bucks and will be forced to drill holes. Here is the mount I found:
Satechi® Dashboard Mount Universal Tablet Car Mount Holder (for 8.9" - 11" Tablets) iPad, Nexus 10, Samsung Galaxy Tab 8.9", Samsung Galaxy Tab 10", S
 
Thanks I may end up there anyway if this doesn't work. I found this here on the site. If it does not work, I am out 40 bucks and will be forced to drill holes. Here is the mount I found:
Satechi® Dashboard Mount Universal Tablet Car Mount Holder (for 8.9" - 11" Tablets) iPad, Nexus 10, Samsung Galaxy Tab 8.9", Samsung Galaxy Tab 10", S
What Tx do you have, The new one with the tilt wheel on the side or the old one ?
 
Well i was going to offer to help, I have a old Tx shell that i could drill for you and swap the covers, but you need the new Tx,
 

Members online

Forum statistics

Threads
143,066
Messages
1,467,356
Members
104,934
Latest member
jody.paugh@fullerandsons.