Recent content by xjmdrone

  1. X

    No image transmission signal - P3P

    I had the same problem at one time. To fix this, you need to put all the files in the same folder C:\ph3pns or try direct to the root folder C:\ make sure you are running cmd as admin
  2. X

    No image transmission signal - P3P

    Hello @quaddamage I had a technician rewire the defective RX pad and re solder all the wires. I tried to re-flash the nand chip as directed as the ph3pns zip file And this time It did flash successfully... :) Thanks a lot for all the help given from you guys with @SunsetCatcher and all the...
  3. X

    No image transmission signal - P3P

    Thanks again. I will report back when the pad will be repair so I can flash again. :)
  4. X

    No image transmission signal - P3P

    Thanks.... that is way above my head as I lost the pad :(. I will ask a skilled technicians to see if it can be done near me. I don't even know if I can still flash the nand as "3 post above" I'm getting ubl1.img not found or BOOTUBL boot loop. What do you think, is it worst a shot to even...
  5. X

    No image transmission signal - P3P

    Hello @quaddamage @SunsetCatcher Is there is an alternative to #6 - RXP to TX FTDI for a connection spot? Thanks
  6. X

    No image transmission signal - P3P

    Hello There I have the message ubl1.img not found ??? I tried two laptop it's weird Sometime I got this too >> Target: Starting UART Boot... Target: BOOTUBL any ID?? Thanks
  7. X

    No image transmission signal - P3P

    I just wonder if anyone who re flash their gimbal has made a instructional video for it? I'm about to do mine, It would be nice to get a walk-trough video made by the pro. Thanks
  8. X

    P3 Firmware FIXED P3P GL300B RC always charge and show disconnected on app FIXED

    Just for information. SUCCESS I pressed and hold all the button possible with the controller ON >> C1, C2, record to the left, shutter to the right, ISO wheel, playback total of 6 button pressed and hold then I power off the controller keep pressing all of then and power on RC and a miracle...
  9. X

    RC USB Failure - Preliminary Failure Analysis and Fix

    Just for information. SUCCESS out of the blue my tablet just partially reconnected. I have now a no signal in RED instead of a grey not connected I pressed and hold all the button possible with the controller ON >> C1, C2, record to the left, shutter to the right, ISO wheel, playback total of...
  10. X

    P3 Firmware FIXED P3P GL300B RC always charge and show disconnected on app FIXED

    I just flew my P3P drone out blind. GL300B controller linked OK to AC. went up, down, left, right, took videos, took pictures all went well. still no connection to any kind of tablet or phones. the controller is some kind of battery bank charging system to my tablet. I called DJI support and no...
  11. X

    RC USB Failure - Preliminary Failure Analysis and Fix

    Anyone has a tip or a hard reset pin on how to reset the controller? I did reflow the USB (put a little more sold, I use a contact cleaner product all over the usb point. tried 10 different cable and they all do is only charging the tablet. The GL300B just work fine with the drone itself , I...
  12. X

    Downgrading RC firmware.

    Hello All. does anyone has the wipe file available and the initial GL300B RC 1.03.2 firmware available please e-mail - [email protected] Thanks a lot
  13. X

    Downgrading RC firmware.

    how you do that when the Go app says disconnected and you don't have a camera icon to connect to P3P?
  14. X

    Downgrading RC firmware.

    Hello hunch, could you e-mail me the wipe file please so I downgrade my GL300B RC Thanks [email protected]
  15. X

    RC USB Failure - Preliminary Failure Analysis and Fix

    I have a kind of the same issue. Phantom 3 pro RC link fine to the AC (control gimbal, take pictures, motor start, and fly fine) but tablet is in charge mode all the time Is the USB defective or only the solding? I tried to reflow but still no success. Thanks all.