After multiple attempts to correct, I gave up and sent back to DJI for repair. That was four weeks to the day from when shipped to when it was returned!! That's ridiculous! They had to replace the main controller board and sonar I believe is what they stated.
When I was filling out the form for...
Did the factory reset. Updated to latest firmware. Next I will calibrate compass and IMU. Is there anything else I should do before my next flight?
Thanks!
Good to know about only being able to be installed on a PC (or mac which I don't have). That would explain my frustration with trying to install the Mac version on the ipad mini 2 last night, lol!! Sorry, I am NOT a Mac or Apple person I only own this mini 2 for the P4.
I will finish the...
I will be driving right past you on my way to UT. I was there (Port Clinton) a few weeks ago for lunch after the National Matches at Camp Perry! If I get up that way again I'll bring the P4!
Another note about the elevation issue. Today I had the P4 on a picnic table (aluminum just in case that...
I see another thread where a P4 owner did a factory reset using the DJI assistant and it corrected his issue. Has anyone here tried that yet? Looks like someone else in the thread tried it but it didn't help.
Factory Reset, Update: It fixed my altitude problems!
I will try that before the...
Was there ever a resolution to this issue? I have the same. I was hovering at about 20 feet to set the POI so I could test that Intelligent Flight Mode. I selected the Point of Interest and got a warning that I must be a minimum of 5m(16ft). When I checked elevation it was -177 feet! I am 20...
Another issue I have is the length of flight time. I have done a lot of work to this quad to extend the flight times. The 1.5 conversion to use the 5200mah lipos, 9443 and 9450 props, upgrade board to eliminate the PMU and GCU (reducing weight), chancing settings in the NAZA assistant, etc.
The...
Hey guys,
I have completed this conversion and even more. Before this upgrade I had a 1.1.1 with the Zenmuse H3-2D w/GCU. I am 100% positive I was able to stop the gimbal tilt at whatever point I wanted.
Now with the upgrade board and the H3-3D gimbal (no GCU b/c it comes off the board) when I...
I have heard of people putting card back into gopro and plugging into computer using the USB cable but I haven't experienced that. If that doesn't work and you are 100% sure you recorded the video or images you can use recovery software. I have used Easus (I think that's what it's called)...
So after all that I forgot to ask what settings everyone is using in the Naza Assistant??
I ran the 9450 blades on my test flights. So I will go with the 9443's my next couple of flights to see if that affects flight time as well.
Sigh...not complaining about the new layout but I find myself getting frustrated trying to find things!! As an example, how do I search a specific thread? I want to search this thread to see if anyone posted their Naza settings after the 1.5 conversion.
On a great note, I have already completed...
Just about done with my conversion!! :) I modeled a mount for my FPV Tx and I will be printing that tomorrow. I want the final to be made from nylon but I only have ABS so that's what it will be for now. Once I get that printed I should be good to get it fired up!! It's been WAY too long.
Re: Video: Fitted my Phantom v1 into a Phantom 2 shell (easy
It was suggested that using the upgrade board and latest firmware that I could use the Zenmuse H3-3D gimbal. I am going to reassemble with the H3-2D for now but my next upgrade will be the H3-3D and I would like more information on...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.