Recent content by mrmom852

Long Story Short.... I had to Buy a Replacement Camera, so a New,Used Camera-Gimble Assembly was Installed on my Drone... and Now the Firmware is at : 1.09.02 .....So I have to Go back through and Downgrade Everything Back to 1.5.7..... to get back to a Free Flying, unrestricted drone...

This was all Solved and Talked about in March 2017 by KennethMcNutt, ....He has it all Explained how to Down Grade... back then... I saved the Pages to my Drone folder on my Puter with a copy of all the different firmware versions... Part of the Reason for Doing this was the Problems I was...

This is a Link From Back in 2017 when It was all Being discussed, No it Contains just about everything to do with Phantom 3 Drones....

Rod....Has anyone been able to downgrade since the 1.9.02 up grade?? I was following and Saved the Posts from May 2017, when This was all being Talked about, I also saved the Links to The Google Cloud site that Has all of the Files for all of the Phantom 3 Drones...

I have all the Files and Saved the Pages when this was Going on back around May 2017.... Google Drive has all the Downgrade Files and The Debug Files for all of the Phantom 3 Drones... https://drive.google.com/drive/folders/0B-OwLuqQde7oUXRGTXVjSmpKZEU

From DJI: 2017-06-29 : firmware 1.9.200 Notes  Please note that firmware update may reset various Main Controller Settings, such as the RT Altitude and Maximum Flight Distance, to factory defaults. Before the update, take note of your preferred DJI GO settings, and readjust them after the...

Any time you have a + sign, you have a problem with the Upgrade, and it needs to be Debugged... So that is why it went ape on you.... There is a conflict between the different moduals ...

Has Anyone Lately...... Been able to Go back to 1.05.7 ....I replaced the Main Board back in 2017 and was at 1.05.7...But this Spring a Hung up Camera, took out the Camera Board, So i replaced the Whole Camera-Gimbal ***... The Software in it was 1.9.2 ..... and IT DID NOT TAKE TO BEING...

Been out of Flying for the Last year... A New Camera Has reset my drone to 1.9.02 ...Can we still Downgrade back to 1.5.7 ??? As we did back in 2017??

The Gyro For the Camera is in the Camera, on the M160A 15191 607AA 1 MAX21100 6-axis MEMS digital gyro + accelerometer Board.... That also has the CMOS and MEMORY Card Holder..... There are 2 Boards inside the Camera, The Chip Number above has all the Stuff to Make the Camera Work, the...

There is a Chip on the Gimbal Control Board, Next to the Motor shaft that reads a Magnet, imbedded in the shaft, to Register the Shafts Position....

After Going Down the Github rabbit hole .... Boy... That Gave Me a Headache.....You need to update your Diagram...The Camera has 2 Boards in it... One is the Camera and Video Possessor, and the Other Has the Brains and Memory Storage for the Whole Drone and Software that Controls everything. as...

https://github.com/o-gs/dji-firmware-tools In Depth Study and Wiki's, How the Firmware and Hardware Work....Down to the Component Level... On DJI Products, including Phantom 3 STD ..... IT MADE MY HEAD HURT...... SO MUCH INFO.....

Check back in the Forums around Aug 2017.... we went all over this.... DJI....CUT THE POWER OUTPUT OF THE TRANSMITTERS..... BECAUSE PEOPLE WERE FLYING CLOSE TO COMMERCIAL AIRCRAFT.....FLYING TO HIGH AND TO FAR AWAY.....

Just Got the New Gimble Control Board, from China, and Installed it this Evening.... What a Pain.... Just Remember to Keep yourself Grounded while working on these Naked Boards....Will Try it tomorrow..... See How it Does.........