Recent content by Mr.P

  1. M

    FPV faulty?

    Yeah it was connected that way. For those of you to come across the same problem I had, this is an excellent solution. https://www.rcgeeks.co.uk/dji-innovatio ... =fpv%20hub
  2. M

    FPV faulty?

    hiya, thanks for your reply. I've discovered since, that its actually a power issue from the board but the usb works fine as does everything else. Is there another way to power the transmitter?
  3. M

    FPV Power supply

    Hi The phantom isn't providing any power from the board, is there another way to give power to the transmitter? Oddly the video cable works but the power doesn't. Thanks
  4. M

    FPV faulty?

    ok, thanks for this. The transmitter is brand new, so could it be a problem inside the phantom? It's wired up correctly. & also is there - to your knowledge a red LED installed on the Emersion RC 5.8 Gz Transmitter?
  5. M

    FRC info.

    Any way still need the above info, can't state that to Resource Group Ltd.. ?
  6. M

    FPV faulty?

    Hiya, installed the immersion RC 5.8Gz 600 mw tx but not getting any signal. Is there a way of telling if it's the tx at fault or the phantom circuitry? I presume as the gimbal is connected to the same board that if the tx is not working then the gimble would also not be working? The receiver...
  7. M

    FRC info.

    Hiya, Yup it is for the Phantom 2 with is 1180g in weight. permission is needed for aerial work which is what this is for regardless of weight? Thanks for your reply :)
  8. M

    FRC info.

    Hi folks, Wondering if anybody has been through the FRC process for the CAA permissions approval? Anyway, I have a few questions relating to this that I'm finding hard to find the info out for. What's the: 1) Maximum take off weight 2) Motor speed (RPM - 900? ) 3) Maximum flight time with...
  9. M

    Yawing

    Solved. There were 4 things I did which helped in addition: 1) I took the foam off the legs to make it even. 2) placed the craft on the floor and not the desk because the floor is more even. 3) Allowed the phantom to 'cool' down for 5 mins before calibration 4) When doing the compass...
  10. M

    Yawing

    Thanks for this. However as there isn't an obvious link within the website, a direct link would be most appreciated :D
  11. M

    No GPS control on Phantom 2

    try the calibration process before flight - e.g. http://wiki.dji.com/en/index.php/Phanto ... he_Compass
  12. M

    Circles, not TBE on a P2

    yeah for me it was upgrading to firmware 3. I get an up and down effect on hover / drift like this: https://www.youtube.com/watch?v=asa5RLN ... e=youtu.be my thread: viewtopic.php?f=5&t=12752
  13. M

    Yawing

    Here's a youtube link to demonstrate the problem further. Note - I'm not providing any input from the transmitter. https://www.youtube.com/watch?v=asa5RLN ... e=youtu.be
  14. M

    Yawing

    Interesting, I did a full calibration last night and flew this morning the phantom also flipped/crashed. Still seems to be 'drifting' though. Appears to be more agile or a sensitivity increase, although it did seem more stable when hovering for a few seconds. My motors are spinning fine...
  15. M

    Yawing

    Ok so now the motors are failing to start due to this error message. When calibrating it's not central on the stick calibration window either - although it is. Any thoughts? Thanks. A. Motors Start failure caused by TX stick(s) mid point error too big If the TX stick(s) mid point error is...