Recent content by Macdougal

Thanks for the quick replay and apparently my eyes are working <smile> I will temporarily hook up my IOSD to be sure on the GPS. The 800 makes my F550 feel like a lightweight...

I have a DJI A2 setup on my S800 and have a problem trying to see the LED GPS lock lights. I believe it flashes two purple when GPS is obtained at less than 50% throttle. The LED kind of looks like a combination of red/purple. They almost look red but when I put a sheet of white paper to...

I have a 14SG and I am trying to change the choices of switches for channel 8 - I show SD SH RS T4 and would like to use switch SF for the retracts. I don't know how to to say change the SH to SF? Any help would be greatly appreciated. I am very new at all of this and this is my first RC...

Thank you for the quick response... I appreciate your help

I have a 14SG and tried to save my program data for my F550. So far all I can do is clone the existing F550 but I would like to back it up so if I make some changes and screw it up I can go back to square one. I have a SD card formatted in the transmitter. Please let me know what I need to do...

I have a F550 with Futaba 14GS and would like to add a DYS 3 axis gimbal. I am a beginner and totally lost on how to do this. I did a little research and found someone suggesting adding a FrSky SBUS & CPPM Decoder with Pins for the additional 3 channels. I am open to whatever it takes to get it...

Is there a way I can look at all the channels that have been programed and see what their function is? The gimbal is powered by a BEC and yes I did read about not powering the servos from NAZA. This is like eating a really big elephant one bit at a time <smile> Thank you for your help...

Thank you very much for your help and I greatly appreciate it... The second item I am adding is a Aeroxcraft VTR-GP which I have on my Aerocraft landing skid. I see how to setup up the gimbal in NAZA would this also need a channel like one of the slide switches on the side?

I have a new 14GS/F550 and need some help programming channel 8 for the retracts. Unfortunately I am new at all of this and have no idea how to do it... Can someone please offer a suggestion or point me to a resource for doing this? All help is greatly appreciated... :D

The only thing powered up is the gimbal. The GoPro is attached with the TL68A10 but not powered up. The shaking I would call violent not high-freq oscillation/vibration. I am going to upgrade the gimbal and motor firmware and check the PID values. I have a 5V BEC rated 3 amps to power the...

I have Tarot 2D V2 and put everything together and I added the TL68A10 GoPro cable for video and 5 volt power and the GoPro is mounted. The only thing I have powered is the gimbal with 12 volts. I do not have it hooked to the receiver or FPV gear. My problem is it shakes like it is going to...

I am waiting for my F550 and Futaba 14GS to arrive. I plan on adding a set of retracts and a Tarol 2D gimbal. I am very new to this and know nothing about the 14GS. Can anyone point me in the right direction? Thanks :D

I ended up sending it to DJI in LA and got it back in about two weeks with new board in the camera. Great service good communication. I was very pleased with the way everything was handled. :D

Are you near Williamstown? Shoot me an email when you can. My email RMARET AT ZOOMTOWN.COM :D

I had a problem and could not fix it. The camera would not bind no matter what I tried. I put in a support ticket with DJI in Hollywood, CA and received a RMA for return. Once they had it in house they acknowledged receiving it and a couple of days later it went to the techs. They notified me...