Recent content by ElecCom

  1. E

    wiring schematic (does anyone have one)?

    All of it is very helpful, thank you so much. Any documentation that helps you to know where and how the internal operation functions. I'm an electrician by trade, and sometimes you see things more clearly when your not just looking at a bunch of wires and circuit boards. A break down of the...
  2. E

    Phantom 2 vision plus power source?

    Thanks for the description on removing the wi-fi unit. I tried touching the leads to the EC connections with the unit on and no luck, I'm afraid if I solder them on they may have an effect on the motors performance. I'm thinking the EC's only get full power when the motors are running?.
  3. E

    wiring schematic (does anyone have one)?

    Anyone know where to get a wiring schematic for a phantom 2 vision plus?
  4. E

    Phantom 2 vision plus power source?

    Does anyone know of an easy way to get full battery power from the inside of the phantom 2 vision plus? I placed a new gimbal and tried to get the power from the control unit (top 2 pins of F2) but the gimbal won't work. I'm thinking its not full power or am I wrong. I would like to know anyways...
  5. E

    Burnt ESC's replaced but speed doesn't increase

    With proper instructions people would know to take the props off. I did do the advance calibration sitting level with props off no-go, tape is a good idea but like I said it idles fine. When it does flip I turn it off immediately. I know no other way but trial and error. DJI's only response...
  6. E

    Burnt ESC's replaced but speed doesn't increase

    I would think DJI would make the software so when you plug the unit in you could turn it on so it tells you if the motor speeds are up to par?
  7. E

    Burnt ESC's replaced but speed doesn't increase

    I found I had the mode one on the assist programed instead of mode 2 so the control sticks were back wards. I corrected this but it still flips, waiting on new motors.
  8. E

    Burnt ESC's replaced but speed doesn't increase

    I swapped what motor I thought was slow but the unit still just flips over when I try to fly. Next I will try all new motors and see what happens.
  9. E

    Phantom 2 Vision+ Camera Ribbon Cables @ DDM

    Re: LIMTED: Phantom 2 Vision+ Camera Ribbon Cables @ DDM Can I just sent the gimbal and camera? I pulled the ribbon cable out already, and when I bought the phantom the gimbal came dismantled already as it must have been crashed.so one motor got separated and the ribbon was broke. Does this...
  10. E

    Burnt ESC's replaced but speed doesn't increase

    Are the ESC's different for a phantom 2, I know they are for a ph 1 (red/green) if so what are the part numbers? My phantom 2 doesn't get up to speed normally after the replacement, when I turn the TX knobs in a different direction the unit just flips, all motors seem to idle fine and go in the...
  11. E

    Burnt ESC's replaced but speed doesn't increase

    Re: help! replaced 2 esc's from used ph 2, now desn't fly??? Thank you smallman28, Yes I did not touch the motors, I bought the ESC's and from what I understood for the phantom 2 and above they are standard, not like the phantom 1 which needed red or green. I soldered the wires back the way...
  12. E

    Burnt ESC's replaced but speed doesn't increase

    Hi guys, I'm a newbie. I just bought two used Phantoms. One is a phantom 2 vision plus which fly's great. The other is a Phantom 2 which had two motors which wouldn't spin. I found it had two burnt esc cards which I bought and soldered on. All motors run, I did calibrations with the software and...
  13. E

    Phantom 2 Vision+ Camera Ribbon Cables @ DDM

    Re: LIMTED: Phantom 2 Vision+ Camera Ribbon Cables @ DDM OK thanks!
  14. E

    Phantom 2 Vision+ Camera Ribbon Cables @ DDM

    Re: LIMTED: Phantom 2 Vision+ Camera Ribbon Cables @ DDM Any way I can get one or two of these ribbons at a reasonable price? I can only find them at http://atkdrones.com/ at a price of $85.00 each. This is totally highway robbery as I'm sure they can be made for less then $15.00 each???