Recent content by Davis476

  1. D

    Bearing replacement - Impossible to remove old bearings

    Thanks for the tip. However won't heat expand the metal and make the bearing tighter?
  2. D

    Bearing replacement - Impossible to remove old bearings

    Hi Everyone, I just got my new ceramic bearings and started working on my phantom. I was able to easily remove old bearings from one of the motors (the noisy one) but cannot seem to get the old bearings out of any of the other three motors. Seems Like they are all pressed in very tightly. one...
  3. D

    Continuous red flashing light VOL-LOW(4) Error?!

    Re: Continuous res flashing light VOL-LOW(4) Error?! Final Diagnosis of this issue. Looks like the back plug of the USB cable going from the LED module over the upgrade board the battery compartment pushes against the wire harness that goes into port X3 on the NAZA. if the USB cable is tugged...
  4. D

    Phatom flight over Honokohau harbor in Kailua Kona, Hawaii

    Testing out my phantom again after fixing a loose solder joint. http://youtu.be/O3d2tfz1JSQ Enjoy!
  5. D

    Continuous red flashing light VOL-LOW(4) Error?!

    Re: Continuous red flashing light VOL-LOW(4) Error?! (SOLVED Well. My solution didn't last.... I still get the Red blinking low voltage lights.Upon further investigation I found tha one of the solder joints broke loose on the main board connector that goes in X3 which delivers voltage data. I...
  6. D

    Continuous red flashing light VOL-LOW(4) Error?!

    Re: Continuous res flashing light VOL-LOW(4) Error?! Well, I opened her up and re-secured all the connections to the NAZA. Seemed to have solved the problem for now.
  7. D

    Continuous red flashing light VOL-LOW(4) Error?!

    Re: Continuous res flashing light VOL-LOW(4) Error?! Both. The battery measures 12.4 on a tester and the assistant also reports a similar voltage...
  8. D

    Continuous red flashing light VOL-LOW(4) Error?!

    Re: Continuous res flashing light VOL-LOW(4) Error?! Thanks, I'll give it a try... Are the smart contacts the black connectors that connect to the NAZA? Or am i looking for something else?
  9. D

    Continuous red flashing light VOL-LOW(4) Error?!

    Re: Continuous res flashing light VOL-LOW(4) Error?! Thanks, I'll give it a try... Are the smart contacts the black connectors that connect to the NAZA? Or am i looking for something else?
  10. D

    Continuous red flashing light VOL-LOW(4) Error?!

    Hi guys, I need your help... This afternoon I powered up my phantom, waited for the light sequence to begin, and right after the first set of green lights I'm getting a continuing rapid red light. Same as when the battery is low. I have 6 new batteries, all fully charged and this happens with...
  11. D

    My first Phantom Video, Kona, Hawaii

    I got scared and didn't want to go over the water for too long... As I gain confidence I will definitely be flying over water and around boats! The gimbal provides great stabilization and I also added some stabilization through Youtube. Thanks!
  12. D

    My first Phantom Video, Kona, Hawaii

    I finally finished setting up my Phantom with a gimbal and Fatshark Predator FPV system. Here is my first video taken at the Old Airport recreational area in Kona, Hawaii. Let me know what you think! http://youtu.be/p6vEo4T3u6w
  13. D

    Water ski

    אחלה!
  14. D

    Normal takeoff?

    Sorry to hear about your troubles. I had the same problem when I got my phantom. and it turned out to be that the compass was installed on the wrong leg. The GPS was getting the bearings all wrong and was compensating in the wrong direction. If you can get a fairly stable hover in ATTI mode but...
  15. D

    GPS tracker

    Which tracker are you using? if your tracker is constantly updating and transmitting, it can interfere with the compass and onboard gps. I use the Garmin gtu-10 and set it to on demand mode. never had any issues.