Recent content by Colombo973

Board is marked "P01007.06" and have the pb free symbol on it. I will try to force upgrade ! I highly prefer to see my bird flying with a fonctional OFDM board instead of a hacked board full of tiny cables and fragile solders.

It's a OFDM v1 for sure, so it mean something bad... is there a way to save it ? Thank you for USB explanation, so i can say i am a little lucky in my misfortune. I hope everything will be ok for this Christmas gift ! Thank you for continued help ! Cheers

Well, i gave up with the OFMD board i've found, always have "[19 00][00] v0.0.0.0 -> v1.0.8.96 need upgrade." and can't link to AC to the RC. So i decided to try something with the first OFDM. First i've planned to deconnect each solder one by one and check by a firmware update to see which is...

Ok, i think there is a continuity default after the soldered pads ripped out. even with a magnifying glass i can't see where copper paths are broken. I was able to find a other OFMD module, supposed to be not working but it look very nice, connector are good. I've checked the test pads and all...

Thanx, i have no doubt about solder of USB D+ and USB D-. The ones i suspect are CANH and USB_SELECT, is it possible ? And there is no more test pads on the board... Could it be a firmware issue ?

Ok guys, due to improper handling some of soldered points i've made on the board have dropped. I've tried to resolder on the pads but it was difficult because some some were torn off. Anyway, after that, everything is fine but i don't have any live view (but it can take picture or video that are...

Well, the technician made a very bad job, i found some doc with test pads on RC Groups, and only one pin have continuity :mad: So i decided to do it myself with a 10$ solder tool. It doesn't look very nice but it works ! Now i have gimbal control, live view, and no more beep ! I've ordered...

Some update. An electronical technician made the job of resoldering the connector, but result is the same, no change. I have serious doubts about his work. Is there a way to verify connectivity on the mainboard ? I've checked all the labaled plots on the mainboard, and only one (GND) have...

Wow, i'm impressed ! I've spent so much time with update procedure, and googling... Ribbon cable is new so i was confident with it but i've checked the connector on OFDM board, and first it appear to be intact. But when i connect the ribbon in it, i see it moving slightly : the welds are broken...

"device not connected" lines are in the hidden txt log, i have no message in DJIGO, only aircraft status indicating the need of firmware update. I'll try to scroll to the advanced. One other thing, i've noticed one blinking red led inside the OFDM module (link led is still green on the side)...

Pro. I'm almost convinced that the "device not detected" lines are due to several hardware issues on the gimbal mainboard that is very sensitive to overheating. But if this mainboard is defective, why led status is solid green ? I need to be 100% sure of that, i don't want to spend a lot of...

Ok, but once you put a p3p camera on a p3a aircraft, i should have to use a p3p firmware ? i've heard that p3a and p3p aircraft are the same, only gimbal/camera differs and defines the model. Is this statement right ?

P3X_FW_V01.11.0020.bin is not supposed to be the same firmware for both P3P and P3A ?

Yes, i always try to update with a fan closed to the quad. Here is what the hidden log give : [00012876]Delete history success. [00013139]========== remo-con disconnect. boot(15) ============ [00013217]Packet [C:\P3X_FW_V01.11.0020.bin] detected, card sn [0x03c6ebb2]. [00013289]Packet...

Hi everybody, I'm stuck with a P3P and i need some help please. Aircraft is a P3A with a P3P camera. At start, aircraft and gimbal power on, and front led on gimbal stay green, but it always emit a mild double beep (DD-DD-DD) that never stop. RC is linked to aircraft correctly. I can access to...